FEC Onlineservices
 
Configuration of VLAN between a funkwerk switch S1224p and funkwerk W2002 with FCI
This FAQ describes how to configure a tag-based (802.1Q) VLAN between a funkwerk S1224p and a funkwerk W2002 over the graphic user interface FCI (Funkwerk Configuration Interface).

Scenario

Preliminary Note:
- Software Release on the Access Point has to be 7.5.1 Patch 5 or higher
- Software Release on the Switch is 1.03
- Please use Microsoft Internet Explorer 6 or higher to configure the devices
- The Access Point W2002 will be powered by PoE (Power over Ethernet) from the switch
- Trunklink between Port 8 on the S1224 and en1-0 on the W2002

1. funkwerk Access Point W2002 configuration
Start your Browser and log in the Access Point.
Select the menu Wireless LAN -> WLAN 1.
Configure the Wireless Settings:
- Operation Mode: Access Point
- Operation Band: 2.4 GHz In/Outdoor
- Channel: 1

Afterwards press OK.

Now select Virtual Service Sets in order to configure the Service Set Parameters.
Configure following:
- Network Name (SSID): VLAN2
- Security Mode: WPA-PSK
- Preshared Key:

Please configure the next Network Name (SSID), VLAN1 and VLAN3 in the same way.



To create the VLANs on the Access Point select menu LAN -> VLAN

We want to manage the Access Point via VLAN ID 1, which is standard for Management. The Management VLAN will be renamed in VLAN 1.
Configure VLAN:
- VLAN Identifier
- VLAN Name
- VLAN Members (this means the interfaces)

You have to configure the VLAN1 to VLAN3 as following:
- VLAN1 with Identifier 1 -> en1-0 tagged, vss1-0 untagged
- VLAN2 with Identifier 2 -> en1-0 tagged, vss1-1 untagged
- VLAN3 with Identifier 3 -> en1-0 tagged, vss1-2 untagged

Usually the WLAN data packets will be transfered untagged.






Under menu LAN -> VLAN -> Port Configuration the respective PVID (Port VLAN ID) will assign to the interfaces. This ensures that over WLAN arriving data packets will be forwarded into the adequate LAN.
- Interfaces en1-0 and vss1-0 get PVID 1 (VLAN 1)
- Interface vss1-1 get PVID 2 (VLAN 2)
- Interface vss1-2 get PVID 3 (VLAN 3)








Under menu LAN -> VLANs remove the interfaces vss1-1 and vss1-2 from VLAN1.

To activate finally the VLAN on the Acess Point go to the menu LAN -> VLAN -> Administration.







2. funkwerk switch S1224p configuration
Start your Browser and log in the switch.
Select the menu Protocol -> VLAN Configuration.

Please select 802.1Q at the VLAN Operation Mode. After a few seconds click on the button Configuration to call up the VLAN configuration interface.



A Default VLAN it exisists in which all Ports are member.
We will use this Default VLAN as VLAN1. Over all 3 VLANs are required. You have to configure Group Name (vlan1, vlan2, vlan3) and VLAN ID (1, 2, 3).
The Access Point is in our example attached on switch port 8.
- For VLAN 1 select with Add Port 1 and Port 8
- For VLAN 2 select with Add Port 2 and Port 8
- For VLAN 3 select with Add Port 3 and Port 8

The procedure as example for vlan2.

After this press on button Next.

On following window configure only Port 8 to tag and confirmed with Apply.
The same procedure carry out with vlan2 and vlan3.



Under menu VLAN Configuration -> Port VLAN ID the following parameters have to be configured:
- For Port 1 the PVID 1
- For Port 2 the PVID 2
- For Port 3 the PVID 3

With this setting will be ensured, that arriving untagged data packets on the Port 1 to 3 will be forwarded into the adequate VLAN.
On Port 8 the data packets have to be provided with a VLAN-tag to distinguish the VLANs.


Successful ping from IP 192.168.100.140 (VLAN 1) to 192.168.100.30 (VLAN 1)
Both IPs are in VLAN 1. All other IPs are from 192.168.100.140 not reachable.

C:\>ping 192.168.100.30

Pinging for 192.168.100.30 with 32 bytes of data::

Reply from 192.168.100.30: Bytes=32 Zeit<1ms TTL=30
Reply from 192.168.100.30: Bytes=32 Zeit<1ms TTL=30
Reply from 192.168.100.30: Bytes=32 Zeit<1ms TTL=30
Reply from 192.168.100.30: Bytes=32 Zeit<1ms TTL=30

Ping statistics for 192.168.100.30:
    Packets: Sent = 4, Received = 4, Lost = 0 (0% Verlust),
Approximate rounde trip times in milli-seconds:
    Minimum = 0ms, Maximum = 0ms, Average = 0ms

C:\>
Unsuccessful ping from 192.168.100.140 to 192.168.100.20 (VLAN 1 to VLAN 2)

C:\>ping 192.168.100.20

Pinging for 192.168.100.20 with 32 bytes of data:

Request timed out.
Request timed out.
Request timed out.
Request timed out.

Ping statistics for 192.168.100.20:
    Packets: Sent = 4, Received = 0, Lost = 4 (100% Verlust),

C:\>

2013 bintec elmeg GmbH